How to Build an Inexpensive Plant Stand


Submitted 2 years ago
Created by
Henry Homeyer

Get Ready Now, Spring Is On the Way

A couple of years ago I replaced all my fluorescent lights and decided to move plants upstairs to the laundry room. My clunky old metal plant stand would be nearly impossible to get up our spiral staircase, so I built a folding wooden one – and you can, too. It took me an hour to build and cost a lot less than buying one.  

                                                      Homemade plant stand

 First, you need to decide if a plant stand is right for you. Mine is a tall narrow triangle in cross section, with 2 shelves.  It is 6 feet tall, 5 feet wide and 2 feet from front to back at the base. It has space for 6 flats or trays, each of which will hold at least 32 plants – more if you buy the smaller six-packs that I avoid (some flats can hold 48-72 plants). You can also  buy more lights and have 3 layers of seedlings - with the bottom layer on the floor. 

Advertisement: Content continues below...

 The lumber for this cost me just under $50 and the light fixtures – 4-foot shop lights – cost me $14 each plus $8 for the fluorescent tubes. The stand uses 3 fixtures, so the lights cost about $65, for a grand total of about $115. Looking at catalogs, I see that one can easily spend $500 or more for an equivalent. One could use the same design to make a similar model that would just have one shelf and use one fixture and cost about $75.  Then, if you decide you like starting plants in the house, you could add a second shelf and buy the extra lights and shelf next year.

 Here is what you need to buy for the model I built:

(10) pieces of 1”x2” pine, 6 ft long                                                                 

(2) pieces ¼” plywood, 2’x4’                                                                          

(1) pair 3” strap hinges                                                                                                     

(3) 4′ shop lights with fluorescent bulbs                                                         

(50)  sheet rock screws (1.25” long)   

Tools: portable drill with magnetic bit to fit the screws and a measuring tape     
 

Lumber yards will cut all your materials to size for you. Some sell plywood in 2ft by 4 ft sheets. If not, you will have to buy a full sized sheet (4×8-ft) which will cost a little more. In any case, your top shelf is 16 inches wide by 4 feet long, the second shelf is 24 inches by 4 feet, so you will need to ask someone to cut the 16 inch piece to size. You will need to ask them to cut the 1×2 pine boards as follows: six 60-inch pieces, four 72-inch pieces, six 12-inch pieces. So if the store does not have 6-ft lengths, get 12-ft lengths and have them cut to length.

                                                     Legs of Plant Stand

 Start by making 2 legs for your plant stand. Lay the 6-ft pieces end-to-end on the floor. Do it on your deck if possible, or next to a wall so that you can get them in a straight line by lining them up with something that is straight. Lay the hinges in place so that you will be able to fold them closed (most hinges only close one way).

Attaching hinges on lets of plant stand

Next close up the hinged legs and place them 5-ft apart on the floor.  Place 3 of the 5-ft pieces on top of the first side. One should be screwed right at the top, one 24 inches from that, and the last 24 inches below that. Flip over the stand, and do the same on that side. Stand it up, and spread the legs 2 feet apart at the bottom. At this point, your tripod will be wobbly. Let’s fix that. 

You have 6 pieces of scrap wood, a foot long, left over from making the 5-ft lengths. You need to attach 2 of these to the inside of the bottom cross pieces, one on the front right, one on the back left. Then place your 24-inch wide shelf on top of the bottom supports and center it. There is 6 inches or so of space on either end of your shelf. See photo below.

 You will now attach a cross brace at a 45 degree angle between the short piece you just installed and a leg. This will keep the plant stand from swaying. Then take another 12-inch piece and attach it across the legs (front to back) 30 inches from the top. That will make prevent the legs from splaying – and make it as sturdy as the Rock of Gibraltar.

                                                       Cross bracing

 Lastly you need to hang the lights. Mine came with S-hooks and chain, which made hanging the lights easy. If yours do not, you will have to buy them. Most shop lights have slots and holes on the back side so that you can slip in S-hooks easily to hang them. You can also open a link of your chain and fit it in without an S-hook, just use 2 pairs of pliers to bend a link open.

                                                       Finished Plant Stand

 Starting seedlings indoors is miraculous for me – even after doing it for decades. I hold my breath waiting for germination, and fuss over the seedlings like a mother hen. And when I bite into my first tomato in August, I have the added satisfaction in knowing I brought that tomato into my world – with a little help from Mother Nature.

Click here to sign up to get an alert by email every time I add a blog entry if you like! And if you like an article, please share it with your friends. Facebook works great, or just copy the web address and e-mail it to your buddies.

I'm the author of 4 gardening books.  Visit my personal website by clicking here.  

 

Comments

Download the DailyUV app today!